Aim Advanced Power Distribution Module Kits

In the past traditional fuse and relay systems were used to distribute and control vehicle electrical circuits. This old method was cumbersome, heavy and sometimes difficult to diagnose problems. This can now be a thing of the past when you use our Advanced PDM Modules (Power Distribution Modules).

Vehicle Power Distribution Just Got a Whole Lot Easier!

By replacing your old conventional relays, circuit breakers and wiring then replacing with an Aim PDM (Power Distribution Module), you would be simplifying the wiring harness, saving time, weight, and improving reliability.

The Aim Advanced PDM08 and PDM32 are engineered using lightweight anodized billet aluminum cases specifically designed to stand the rigours of the Motorsport environment. Sleek and stylish, they are easy to fit into most vehicles allowing you to simplify your wiring harness and electronics installation, whilst providing much more control of your vehicle power distribution installation.

Introducing… Aim Advanced PDM Modules 

In the past traditional fuse and relay systems were used to distribute and control vehicle electrical circuits. This old method was cumbersome, wieghty and sometimes difficult to diagnose problems. This can now be a thing of the past when you use our Advanced PDM Modules (Power Distribution Modules).

AIM PDM32 AND PDM08 ARE ALSO POWERFUL DATA LOGGERS !

Our Smart, easy installable PDM 32 and PDM08 Modules offer a simple, highly controllable power wiring solution but with some seriously major advantages, both Aim PDM modules are Data Loggers. This means they connect and read data from your ECU (Engine Control Unit) allowing you greater control over the whole vehicle power distribution network.

An Advanced PDM Kit That Does it All!

FLEXIBILITY – AVAILABLE IN 4 CONFIGURATIONS

AIM PDM32 with 10″ DISPLAY

AIM PDM32 with 10" DISPLAY

AIM PDM32 with 6″ DISPLAY

AIM PDM08 with 10″ DISPLAY

AIM PDM08 with 10″ DISPLAY

AIM PDM08 with 6″ DISPLAY

AIM PDM08 with 6″ DISPLAY

Built in Safety When Racing Goes Wrong…

Safety in all aspects of Racing and Road driving, is of paramount importance. Aim Advanced PDM Modules allow you to to pre-configure aspects of the vehicle power supply to ‘switch off ‘ in given conditions, for example, in an accident or impact. This is a positive safety feature, particularly in Motorsport, as it protects the driver from potential spilt fuel ignition.

Mirror Camera

PDM32 features two analog camera inputs that allow you to swap your display into a mirror camera with the press of a button or through configurable event logic-reverse gear most commonly.

Power Outputs

The PDMs offer four different Power Outputs Levels: Each output provides status feedback for open circuit, short circuit, high temperature, over current, under voltage and over voltage

Inrush current, number of fault retries and the time between retries are all definable.

All the outputs may be configurable as PWM and allow soft start/stop.
For every output, a multicolor LED shows the status:

  • Enabled/disabled
  • Activated or not
  • Fault

CONTROL ALL YOUR POWER OUTPUTS

Race Studio 3 Software (Included with the PDM Pack), offers a clear visual interface, to configure all your power outputs. This gives you a lot of flexability with any vehicle wiring installations.

Special Functions

Some “black boxes” are available for simplifying the configuration.
For example, the Wiper may be managed by the LIN connection or using the Half Bridges.
In this case, you may take advantage by a virtual object like the following one:
SPECIAL FUNCTIONS

Inputs

PDMs feature the following Inputs channels:

If configured as Analog inputs, it is possible to activate an internal 2K Ohm resistor, for connecting most of the sensors directly.

If configured as Digital Inputs, it is possible to activate a 10K Ohm Pull Up or a 10K Ohm Pull Down.

Powerful Data Management

The PDMs receive, use and record data from:

  • ECU: more than 1,000 protocols available
  • Digital/Analog inputs
  • Internal 9 axis EMU
  • GPS: position and Lap Time
  • Expansions
  • Pushbuttons, from RIO02 Module or from any commercial CAN keypad, thanks to the simple configurability of the CAN protocols
  • All the currents and status of all the power outputs
  • Other user defined math channels

Data Logger

An internal datalogger is available, capable of recording all the analog inputs, digital inputs, ECU channels, GPS values, Currents, status of all the Power Outputs. Here an example of what the recorded data may show, during engine cranking.

  • In red, the ignition pushbutton
  • In blue, the battery voltage drop
  • In purple, the current absorbed by the solenoid
  • In dark green, the current absorbed by the fuel pump
  • In green, RPM Value

GPS INCLUDED WITH AIM PDM’S

PDMs come with 4,000 tracks in their database and automatically select the one you are driving on. 

Aim GPS samples ten times per second position, speed and lateral/in-line acceleration at any point of the track and is more precise than most of the existing GPS systems, as it has been designed to add to the GPS satellite’s signal the Global Navigation Satellite (Glonass) system’s signal.

With an average of almost twenty satellites working in conjunction, GPS08 guarantees a precision and a reliability simply not comparable to the old generation GPS systems.

NO OTHER COMPARIBLE PDMS, COME WITH STUNNING DISPLAYS

FOR A SIMILAR PRICE!

DID SOMEONE SAY FREE SOFTWARE?

All our PDM’s come with Free Race Studio Software 

  • INTERNAL DATALOGGER no need for another logger
  • EASY REPLACEMENT of traditional fuse & Relays
  • HIGHLY ENGINEERED  to handle the rigours of Motorsport
  • SIMPLIFIES YOUR WIRING HARNESS and offer more control
  • LIGHTER WEIGHT than the old fuse and relay boxes
  • SAFETY SOLUTIONS Can be controlled by the Datalogger
  • GPS MODULE comes with 4000 tracks installed
  • FLEXIBILITY – FOUR KIT CONFIGURATION CHOICES
  • ECU CONNECTION, for getting data from your ECU
  • STUNNING DISPLAY, 6″ or 10″ options to fit most vehicle sizes
  • GPS MODULE, automatic lap times and track positions
  • DASH CONTROLLER, for easily managing a 6” or 10” dash
  • 9 AXIS EMU PLATFORM
  • MIRROR CAMERA OPTION, for easy reversing

WHICH ONE DO YOU NEED FOR YOUR CAR PROJECT?

AIM PDM32 with 10″ DISPLAY

AIM PDM32 with 10" DISPLAY

AIM PDM32 with 6″ DISPLAY

AIM PDM08 with 10″ DISPLAY

AIM PDM08 with 10″ DISPLAY

AIM PDM08 with 6″ DISPLAY

AIM PDM08 with 6″ DISPLAY

NEED HELP? CALL US ON Tel: 01782 393843